Cylinder Heads

Find products for your vehicle

            110567Y00A - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-7Y00A
            $5.87
            $2.21 (27%) below MSRP $8.08 About MSRP
            11056EN20A - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-EN20A
            From 06/2011. To 06/2011.
            $4.92
            $1.86 (27%) below MSRP $6.78 About MSRP
            1105653F01 - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-53F01
            All Required.
            $7.89
            $2.98 (27%) below MSRP $10.87 About MSRP
            110561CA0A - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-1CA0A
            $10.08
            $3.80 (27%) below MSRP $13.88 About MSRP
            140351KC0A - : Gasket-Manifold To Cylinder Head for Nissan Image

            Gasket-Manifold To Cylinder Head

            Nissan 14035-1KC0A
            Juke. Sentra. 1.6l turbo.
            $38.25
            $14.43 (27%) below MSRP $52.68 About MSRP
            110565NA0B - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-5NA0B
            $9.34
            $3.52 (27%) below MSRP $12.86 About MSRP
            11056ED000 - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-ED000
            Bolt for Cylinder Head.
            $5.60
            $2.12 (27%) below MSRP $7.72 About MSRP
            11056JK21B - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-JK21B
            From 03/2015.
            $12.00
            $4.53 (27%) below MSRP $16.53 About MSRP
            11056F6501 - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-F6501
            All Required.
            $17.11
            $6.46 (27%) below MSRP $23.57 About MSRP
            11056ZB00A - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-ZB00A
            USA Built. To 05/2005. From 06/05. To 06/05.
            $7.87
            $2.96 (27%) below MSRP $10.83 About MSRP
            1105631U10 - : Engine Cylinder Head Bolt for Nissan Image

            Engine Cylinder Head Bolt

            Nissan 11056-31U10
            To 02/2015.
            $9.98
            $3.77 (27%) below MSRP $13.75 About MSRP

            No results found for "Cylinder Head -nut -air -curtain -gasket, Head -nut -air -curtain -gasket, Compressor Head -nut -air -curtain -gasket, Head Gasket -nut -air -curtain -gasket, Cylinder head Gasket -nut -air -curtain -gasket, Gasket -nut -air -curtain -gasket". Here are some helpful search tips:

            • Search by a part name. Example: water pump.
            • Be less specific. Example: brake instead of ceramic brake.
            • Remove information such as make, year or model.
            • Can't find the part you are looking for? Contact us and we'll find it for you!


            How Cylinder Heads Power Your Nissan Engine

            You've got a lot of options when it comes to buying parts online, but shopping with Chapman Nissan is the right choice every time. The cylinder head caps off your engine block and creates the sealed environment where combustion happens. This casting contains all the valvetrain components that allow air and fuel to enter cylinders and exhaust gases to exit after combustion. Without an intact cylinder head maintaining proper sealing and temperature control, your engine will experience reduced power, poor fuel economy, or complete failure. Understanding how cylinder heads function and recognizing failure symptoms helps you address problems before they cause extensive engine damage.

            What Cylinder Heads Actually Do in Your Engine

            Cylinder heads bolt to the top of your engine block and house the intake and exhaust valves that open and close at precise intervals. In your Nissan Kicks or Nissan Armada, the head contains machined valve seats where valves seal tightly during compression and combustion strokes to contain cylinder pressure. Internal passages route incoming air-fuel mixture to intake ports and direct exhaust gases away through exhaust ports. The head also incorporates coolant channels that circulate antifreeze around combustion chambers to remove heat and maintain safe operating temperatures. Combustion chamber design cast into the head's lower surface determines compression ratio and affects fuel efficiency and power output. Camshafts mounted in or above the head operate rocker arms or directly push valve stems to control valve timing. Genuine Nissan cylinder heads are cast and machined to precise tolerances that ensure proper valve sealing, coolant flow, and timing belt alignment, while generic heads often have dimensional variations that compromise performance.

            Common Reasons Cylinder Heads Crack and Warp

            Cylinder heads fail when subjected to extreme heat or mechanical stress beyond their design limits. Engine overheating from coolant loss, thermostat failure, or radiator problems causes aluminum heads to expand beyond their elastic limit, creating permanent warping that prevents proper sealing against the block. Localized hot spots from cooling system restrictions can crack the casting between valve seats or through coolant passages. Pre-ignition and detonation create pressure spikes that fracture combustion chamber walls. Improper head bolt torque sequence or specifications during installation produces uneven clamping forces that warp the head over time. Freezing coolant can crack passages when water expands. Aftermarket cylinder heads commonly use lower-grade aluminum alloys with different thermal properties that make them more prone to warping under normal engine temperatures compared to factory specifications.

            Spotting Signs Your Cylinder Head Needs Replacement

            Replace the cylinder head when white smoke from the exhaust indicates coolant entering combustion chambers through cracks or failed gaskets. Loss of coolant without visible external leaks suggests internal head cracks. Cylinder compression or leak-down tests showing poor sealing between adjacent cylinders point to head gasket failure often accompanied by head warping. Milky oil consistency indicates coolant mixing with engine oil through head breaches. Overheating that persists after cooling system repairs may result from head cracks allowing combustion pressure into coolant passages.

            Discover why mechanics turn to Chapman Nissan first – browse our extensive inventory today.